BUNDLE DEAL: ZUHNE Oslo Lunar Workstation Sink + Una Faucet + Free Qube Bin

• Pull-down kitchen mixer in solid 316 stainless steel. Natural Steel with Natural sinks, Graphite Black with Gunmetal sinks.
• Spanish Sedal ceramic cartridge tested to 500,000 cycles. Swiss Neoperl aerator.
• Two spray modes, 360-degree swivel and a counterweighted pull-out hose.
• Water-saving 2-tick PUB rating, under 6 litres per minute.
• Installed height 42 cm, spout height 20.5 cm, spout projection 23 cm. 5-year parts warranty.

View the Una faucet page

• Model: Oslo V6. Single-bowl workstation sink.
• Material: 316 marine-grade stainless steel.
• Bundle: Oslo sink with accessories, Una pull-down faucet, Reeva soap dispenser and Qube sensor bin (9 litre free, 15 litre +$20, 21 litre +$40).
• Natural finish: Lunar embossed texture in a soft matte finish, with a clear nano coating.
• Gunmetal finish: Lunar embossed texture in a gunmetal colour, applied with PVD (physical vapour deposition), with a clear nano coating.
• Steel thickness: 1.5 mm (16 gauge), uniform across the bowl.
• Deck rims: 3.0 mm thick.
• Corners: R10 (10 mm radius).
• Sound and thermal insulation: Zuhne Pro+ Sound Pads, over 4 mm thick and covering up to 90% of the sink exterior, plus thermal insulation over the entire sink.
• Installation: Undermount, topmount or flush mount.
• Tap deck: 35 mm (left), 35 mm (centre), 28 mm (right).
• Drain: 140 mm, rear-right corner.
• Sink weight: 13 kg (60cm), 14 kg (70cm), 15 kg (80cm).
• Cabinet depth: needs a standard 600 mm deep cabinet or deeper.
• Accessories: about 400 × 270 mm each (cutting board, defrosting tray, drying rack, soak + rinse bin).
• Warranty: Limited Lifetime Warranty against material defects. Colour finishes applied by PVD, such as gunmetal, are not covered.

Oslo needs a standard 600 mm deep cabinet (or deeper). Check the sink's overall length against your cabinet's internal width, and use the size comparison above.

Solid plywood support is strongly recommended, because Zuhne sinks are heavy-duty. Most Singapore installations seat the sink's rim in a recess in the wooden base under the countertop surface. The Installation, Care & Warranty Guide shows how.

Sinks have a size tolerance, so the template is a guide. Aim for the size shown plus 1 mm on each side, never smaller, and dry-fit before sealing.

Yes, in most cases. Oslo's deck has three pre-drilled holes: 35 mm (left), 35 mm (centre) and 28 mm (right). Here is where each fitting usually goes.

• Main kitchen tap: The centre hole is the natural position. The left hole is also 35 mm, so a main tap can go there too.
• Water filter taps: Most need a 35 mm hole, so mount them on the left. That keeps them away from the drain and pipes on the right. With less congestion, the filter system is easier to replace or service later.
• Cup rinsers: Most need a 28 mm hole, so the right hole is the best fit. Cup rinsers have a large base, so the base sits on the countertop, not on the sink deck. The deck is 2 cm below the sink rim, so check the neck length before you buy. For flush mount or topmount, the neck must clear 2 cm. For undermount, the neck must clear 2 cm plus your countertop thickness. For a 2 cm countertop, that means at least 4 cm.
• Soap dispensers: Most also need a 28 mm hole, so they go on the right. Zuhne's Reeva soap dispenser fits holes from 28 to 35 mm, so it can go on the left or right.
• Unused holes: The sink is delivered with all 3 hole covers, loosely attached to the holes. Remove a cover to fit a tap or accessory. If you're not using a hole, silicone its cover in place to seal it.

Please check before you buy: Hole size, neck height and under-deck space differ between brands and models. It is the customer's and contractor's responsibility to check the installation requirements of any third-party product against Oslo's hole sizes and the cabinet layout before buying. We can only confirm compatibility for Zuhne products.

The sink base slopes toward the drain, so water tends to drain quicker and pool less. The tap deck has a slight gradient toward the bowl, so water drops on the deck are guided into the sink. As with any sink, a little water can remain after use, and that's normal.

Scratch-resistant means it stands up better to everyday use and makes fine marks much harder to see. It does not mean scratch-proof, and no stainless steel is. Dragging heavy pots, steel wool and abrasive pads can still mark it. A sink mat or bottom grid helps in busy areas.

The Lunar texture is embossed into the steel. The clear nano coating over it makes cleaning easier and thins gradually with use. The stainless steel and its texture underneath aren't affected.

Yes to all three. The Oslo V6 drain can be attached to wall outlets and floor outlets, and directly to hard PVC piping. The hose can be trimmed at the smooth bands, and the stepped adapter's rings give a firm fit. See the Drain Kit Schematic in Downloads.

The gunmetal colour is applied using the latest-generation PVD (physical vapour deposition) technology, which binds the colour to the sink at a molecular level. That makes it long lasting, but not permanent. A deep accidental scratch may reveal the natural colour of the steel. The gunmetal colour is not covered by the Limited Lifetime Warranty.

Yes. Choose the sink on its own: Oslo Lunar Natural or Oslo Lunar Gunmetal. You can also add the Una faucet there.

Yes. See the Oslo Honeycomb bundle. The two models have different drawings and cutouts, so each bundle has its own downloads.

Both textures are embossed into the steel and help resist scratches. Honeycomb's bolder pattern hides micro-scratches best, and Lunar is smoother and easiest to wipe clean.

Built to be quiet. Zuhne's own Pro+ Sound Pads are over 4 mm thick (most sinks use about 1 mm) and cover up to 90% of the sink exterior (most cover around 20%). Thermal insulation covers the entire sink. Together they keep running water and clattering pots quiet. We don't quote decibel figures, because noise depends on your faucet, water pressure and what you're washing. The easiest way to judge is to see it in person: visit our Experience Centre to check the build and do a knock test.

Yes. Visit our Experience Centre at Wisma Atria Office Tower, Level 11, 435 Orchard Road. Walk in on weekdays 10am to 6pm and Saturdays 10am to 2pm. Closed on Sundays and public holidays.