LIMITED TIME: USE CODE SG50 FOR $50 OFF, MIN. SPEND $699 LIMITED TIME: USE CODE SG50 FOR $50 OFF, MIN. SPEND $699

ZUHNE Una 316 Stainless Steel Pull-Down Kitchen Mixer

$328.00

A pull-down kitchen mixer made from solid 316 marine-grade stainless steel. Choose it to complete a new Zuhne sink in your BTO, or to replace a tired tap in any condo kitchen with a standard 35 mm tap hole. It fits Singapore fittings with no adapters.

Why Una

Solid Steel, Inside and Out

Solid 316 Marine Grade Stainless SteelNot plated brass. The body is 316 stainless steel, which resists rust, pitting and harsh cleaners in Singapore's humid air. Lead-free.
One-Piece LeverThe lever is cast as a single piece, with no welded joint to loosen or leak over time.
Slim 30 mm BodyOne even 30 mm column from base to spout, on a short 48 mm tapered base. A clean, flush look on the counter.
Covered for 5 YearsA 5-year parts warranty covers defects in materials and workmanship, including leaks caused by a defect.

Everyday Use

Made for Real Kitchen Work

Pull-Down SprayThe spray head pulls out to rinse every corner of the sink, and a counterweight brings it back smoothly.
Spray or StreamOne stainless steel button switches between a strong rinse spray and a soft aerated stream.
Room for Big PotsThe high-arc spout swivels 360 degrees, with 221 mm reach and 201 mm clearance under the spout.
Smooth for YearsA Spanish Sedal ceramic cartridge tested to 500,000 cycles, and a Swiss Neoperl aerator with touch-clean nozzles that wipe free of limescale.
Water-SavingUnder 6 litres per minute, without a weak stream.

Will It Suit My Kitchen?

New Sink or Replacing a Tap

With a Zuhne SinkUna is the matching tap for Oslo and Neste sinks. Choose Natural Steel or Graphite Black. It fits the 35 mm centre hole on the sink deck, so your countertop needs no drilling. Fit it with the stabilisation spacer from the box (see Installation).
Replacing an Old TapUna fits any standard 35 mm tap hole in a counter or sink deck up to 30 mm thick. It connects to Singapore's standard 1/2" angle valves with no adapters. Only a cold supply? That works too (see FAQ).

Buying a sink as well? The Oslo Lunar, Oslo Honeycomb and Neste bundles include Una and a free Qube sensor bin.

Dimensions

Size and Specifications

Una kitchen mixer dimension drawing: 400 mm overall height, 221 mm spout reach, 201 mm spout height, 30 mm body and 48 mm base
All dimensions in mm, ±2 mm.
Overall height 400 mm
Spout height 201 mm, counter to aerator
Spout reach 221 mm
Body / base Ø 30 mm column on a Ø 48 mm base
Tap hole Ø 35 mm, in a counter or deck up to 30 mm thick
Material Solid 316 marine-grade stainless steel, lead-free
Type Single-lever hot and cold pull-down mixer
Spout 360° swivel, high arc
Spray modes Aerated stream and rinse spray
Cartridge Sedal ceramic (Spain), 500,000 cycles
Aerator Neoperl (Switzerland), touch-clean
Flow rate Under 6 L/min, water-saving
Water supply 0.5 to 7.5 bar, hot water up to 60 °C
Supply hoses 2 × braided stainless steel, G1/2 × 60 cm
Finishes Natural Steel, Graphite Black
Warranty 5-year parts warranty

Installation

Three Inserts, Three Jobs

For your plumber: under the tap body are three metal inserts of different lengths. Each has one job. Connecting them the wrong way round is the most common installation fault, so please check them before connecting anything.

Shortest: HotConnect to the hot water supply, on the left.
Medium: ColdConnect to the cold water supply, on the right.
Longest: Spray hoseThe one in the centre. For the pull-out hose's nylon quick connector only. Never a water supply.
Diagram of the three inserts under the Una: shortest hot on the left, medium cold on the right, longest in the centre for the spray hose
Left and right as you face the tap from the front of the sink.

Installation Steps

  1. Turn off the hot and cold valves. Flush the supply lines to clear sand and debris.
  2. Screw one braided hose onto the shortest insert (hot) and the other onto the medium insert (cold).
  3. Feed the hoses through the 35 mm hole. On an Oslo or any sink deck, or a countertop under 20 mm, fit the stabilisation spacer first (see below), then the washers and locking nut. Before tightening, turn the tap so the lever faces the front or the side, whichever you prefer. Then tighten until the tap is firm.
  4. Click the spray hose's nylon connector onto the longest insert and tug to check it's locked.
  5. Fit the counterweight at the lowest point of the hose loop, about 350 mm below the counter.
  6. Connect hot to the left valve and cold to the right valve. Open slowly and check for leaks.
  7. Test: lever left gives hot, lever right gives cold, and the spray head returns by itself.

No hot water supply? Una still works. Your plumber splits the cold line with a standard T or Y splitter and connects cold water to both hoses.

Don't Skip the Spacer

Required on Oslo sinks, any sink deck, and countertops under 20 mm thick. Without the triangular spacer, the tap can work loose and wobble. The spacer is in the box. Under the sink, slide it onto the threaded adapter (part 23) flat side up against the deck, then fit the rubber washer (24), metal washer (25), locking nut (26) and its screws (27). Part numbers match the exploded view in the Installation Guide.

Without the spacer the tap wobbles. With it the tap stays firm. Under the sink, in order: threaded adapter (23), spacer flat side up (32), rubber and metal washers (24, 25), locking nut and screws (26, 27). Required on Oslo sinks, any sink deck and countertops under 20 mm.

Installing? Hand the Critical Plumber Checklist in Downloads to your plumber. One page, English and 中文.

What's Included

In the Box

  • Una faucet, with the three inserts fitted
  • Pull-out spray hose and quick-connect counterweight
  • 2 braided stainless steel supply hoses (hot and cold), G1/2 × 60 cm
  • Locking nut, washers and fixing screws
  • Under-sink stabilisation spacer (required on Oslo and other sink decks, and counters under 20 mm)
  • Neoperl aerator key

Downloads

Guides and Drawings

Files open in a new tab.

Care and Warranty

Look After It, and We Look After You

Every Una comes with a 5-year parts warranty against defects in materials and workmanship, including leaks caused by a defect. Labour is not included. Installation must follow the guide, including the correct insert connections. The full terms are in the Installation, Care & Warranty Guide above.

Everyday care is simple: mild dish soap and a soft cloth, then wipe dry. Avoid bleach, acidic cleaners, steel wool and scouring pads. If the flow drops, clean the aerator screen with the key provided.

Questions

Frequently Asked Questions

Will Una fit my existing tap hole?

Una needs a 35 mm hole, which is the standard size for kitchen taps, in a counter or sink deck up to 30 mm thick. If your current tap has a single hole of this size, Una will fit.

Do I need adapters in Singapore?

No. Una connects to standard Singapore 1/2" angle valves with the hoses in the box.

Which insert connects to what?

The shortest is hot, on the left. The medium one is cold, on the right. The longest, in the centre, is only for the spray hose's nylon connector and must never be connected to a water supply. See Installation above, or the Critical Plumber Checklist in Downloads.

Can Una work without a hot water supply?

Yes. If your kitchen only has a cold line, your plumber can fit a standard T or Y splitter to feed both the hot and cold hoses with cold water.

Can I choose if the tap handle/control lever faces the front or the side?

Yes, either way. The lever position is set when the tap is installed, so tell your plumber which you prefer before the tap is tightened. Changing it later means loosening and refitting the tap. The spout swivels 360° in both positions, so it always reaches the whole sink.

Which finish should I choose?

Una comes in Natural Steel and Graphite Black. Natural Steel matches Zuhne's Natural sinks. Graphite Black is a deep, dark finish, a darker shade than Zuhne's Gunmetal sinks.

What does the warranty cover?

A 5-year parts warranty covers defects in materials and workmanship, including leaks caused by a defect. It provides replacement parts. Labour, and damage from installation that doesn't follow the guide, are not covered.

Can I see it in person?

Yes. Visit our Experience Centre at Wisma Atria Office Tower, Level 11, 435 Orchard Road. Walk in on weekdays 10am to 6pm and Saturdays 10am to 2pm. Closed on Sundays and public holidays.