BUNDLE DEAL: ZUHNE Neste Honeycomb Workstation Sink + Una Faucet + Free Qube Bin

• Pull-down kitchen mixer in solid 316 stainless steel.
• Spanish Sedal ceramic cartridge tested to 500,000 cycles. Swiss Neoperl aerator.
• Two spray modes, 360-degree swivel and a counterweighted pull-out hose.
• Water-saving, under 6 litres per minute.
• 5-year parts warranty.

View the Una faucet page

• Model: Neste V5. Workstation sink, single bowl (86cm also in low-divide double bowl).
• Material: 316 marine-grade stainless steel.
• Finish: Honeycomb embossed texture, with a clear nano coating.
• Steel thickness: 1.5 mm (16 gauge).
• Bowl depth: 250 mm. Corners: R10 (10 mm radius).
• Installation: Undermount (5 mm negative reveal recommended), topmount or flush mount.
• Tap holes: none pre-drilled. Any tap, hole size and position on your countertop.
• Drain: 140 mm, offset, reversible (left or right).
• Sound and thermal insulation: Zuhne Pro+ Sound Pads, over 4 mm thick and covering up to 90% of the sink exterior, plus thermal insulation over the entire sink.
• Countertop depth: suits standard 600 mm deep cabinets, and shallower countertops down to 550 mm.
• Certifications: lead-free, US and Canada safety codes.
• Warranty: Limited Lifetime Warranty against material defects.

The sink in your chosen size, a hardwood cutting board, a defrosting tray, a soak + rinse bin, a drying rack, a 140 mm drain kit with a 2-stage strainer, mounting hardware and a cutout template. The bundle adds the Una faucet and a Qube sensor bin.

The countertop overhangs the sink rim by 5 mm on all 4 sides, so the silicone joint is tucked under the countertop edge. It stays drier because water wiped off the counter falls past it, and mould needs moisture to grow. The edge also stays easy to wipe, with no rim to catch crumbs.

Use the size in the table for your model. For a 5 mm negative reveal undermount, the cutout is the basin size minus 10 mm (5 mm each side). For topmount or flush mount, it is the basin size plus 10 mm (5 mm each side). Sinks have a size tolerance, so the template is a guide. For undermount, aim for the size shown, within 1 mm on each side. For topmount and flush mount, use the size shown plus 1 mm on each side, never smaller. Dry-fit before sealing.

Yes. Neste has no pre-drilled deck, so the hardware mounts on your countertop and you choose the hole size and position for each fitting. Check the installation requirements of any third-party product, and have your fabricator mark and drill the holes to your layout. We can only confirm compatibility for Zuhne products.

Neste is compatible with standard 600 mm deep cabinets, and can also be installed on countertops that are less deep, down to a minimum of 550 mm. Check the sink's overall size (460 mm front to back) against your layout, and confirm with your ID.

A solid base is strongly recommended, because Zuhne sinks are heavy-duty. The sink's rim sits in a recess in a base under the countertop surface, and the base carries the weight of the sink. Moisture-resistant plywood is the usual choice, and a cement base or a solid WPC board also works if it is flat and fully supported. The Installation, Care & Warranty Guide shows how.

The 5 mm negative reveal helps, as the countertop shelters the joint. Always insist your contractor uses high-quality neutral-cure anti-fungal silicone, for example Dow Corning (DOWSIL) 798 or 688, or Selleys S601.

316 contains molybdenum, which makes it significantly more resistant to rust, chlorides and acids than standard 304 steel. It is the better choice for hygiene and longevity in humid kitchens.

Yes. The offset drain position is reversible, left or right. Your plumbing outlet is usually still in the centre, so choose by how you work: wash close to the drain so water drains away without pooling, and keep the other side as a dry prep zone, away from splashes. Tell us your preference when you order, or confirm with your ID.

Scratch-resistant means it stands up better to everyday use and makes fine marks much harder to see. It does not mean scratch-proof, and no stainless steel is. Dragging heavy pots, steel wool and abrasive pads can still mark it. A sink mat or bottom grid helps in busy areas.

The Honeycomb texture is embossed into the steel and is permanent. The clear nano coating over it makes cleaning easier and thins gradually with use. The stainless steel and its texture underneath aren't affected.

Boiling water is fine for the steel, but let it cool for a few minutes or run the cold tap while draining, to protect your PVC pipes. Avoid placing hot pans straight from the oven onto the sink. Use the drying rack or defrosting tray as a trivet.

Yes, all accessories can be purchased separately. The stainless steel accessories are dishwasher safe and rarely need replacement. The hardwood cutting board is the only item that may need replacing after years of use, and it should be hand-washed only.

Yes. Choose your size on its own page: 62cm · 70cm · 78cm · 86cm single bowl · 86cm low-divide double bowl.

Built to be quiet. Zuhne's own Pro+ Sound Pads are over 4 mm thick (most sinks use about 1 mm) and cover up to 90% of the sink exterior (most cover around 20%). Thermal insulation covers the entire sink. Together they keep running water and clattering pots quiet. We don't quote decibel figures, because noise depends on your faucet, water pressure and what you're washing. The easiest way to judge is to see it in person: visit our Experience Centre to check the build and do a knock test.

Yes. Visit our Experience Centre at Wisma Atria Office Tower, Level 11, 435 Orchard Road. Walk in on weekdays 10am to 6pm and Saturdays 10am to 2pm. Closed on Sundays and public holidays.